[2017-01-15] Version 1.5
-Changed window position and size
-Does not disengage X-Plane built-in autopilot when the G1000 autopilot is not engaged

[2017-07-12] Version 1.6
-Added date sychronization
-Added panel light synchronization for the backlight of the hardware bezel

[2018-02-14] Version 2.0
-Added AP master switch synchronization
-Added auto-connection
-UDP port changed, not compatible with older versions

[2018-05-06] Version 2.1
-Automatically start up the plugin when X-Plane is loaded

[2018-06-11] Version 2.2
-Temperature unit(Fahrenheit or Celsius) for CHT, EGT and Oil is now read from .acf file every time an aircraft is loaded

[2018-07-09] Version 2.3
-Standby battery is now also a part of which controls PFD turning on or off
-Transponder ident command is now sent to X-Plane 11(needs PFD v4.3.0 or later)

[2018-09-06] Version 2.4
-Standby battery is now isolated from the main battery

[2019-01-02] Version 2.5
-Send status of the 3 switches(standby battery, master, avionics) to PFD immediately after the connection is established

[2019-02-14] Version 2.6
-Hide bridge window on start

[2019-03-31] Version 2.7
-Synchronizing engine hour from X-Plane 11(requires PFD&MFD v5.1.0)

[2019-07-22] Version 2.8
-Fixes a bug causing turn rate is not sent correctly from X-Plane

[2019-12-16] Version 2.9
-All settings are now saved
-Added an option for controlling hardware bezel backlight from a switch in X-Plane
-Added settings to map some unused buttons on hardware audio panel to X-Plane's datarefs or key strokes

[2019-12-17] Version 2.10
-UI adjustment

[2020-08-06] Version 3.0
-Added support for hardware switch panel and standby gauges
-Added support for more engine types

[2020-08-23] Version 3.1
-Added volume controls(for apps 6.0.0 and above)

[2020-09-07] Version 3.2
-Replace engine RPM with prop RPM to show the correct RPM for those planes with a reduction gearbox

[2020-09-08] Version 3.3
-Modified the calculation of the engine load percentage

[2021-01-08] Version 3.4
-Replace engine torque with prop torque to show the correct value
-Add 1.5V to bus E for Carenado CT182T to eliminate low volt warning on the PFD

[2021-02-22] Version 3.5
-Adds option 'reverse' for hardware compass
-Adds support for GA(go around) button on the hardware cockpit panel
-Adds support for alternate static source lever on the hardware cockpit panel

[2021-03-07] Version 3.6
-Improve support for hardware flaps lever and indicator

[2021-11-07] Version 3.7
-Adds synchronization for G1000 failures
-Adds motorized trim wheel hardware support

[2021-11-11] Version 3.8
-Window is hidden by default
-G1000 failures now can be set on the bridge

[2021-12-21] Version 3.9
-Adds rudder trim data output
-Fixes acceleration calculation

[2022-04-17] Version 3.10
-Adds support for hardware fuel valve and fuel selector

[2022-09-07] Version 4.0
-Fixes crash in X-Plane 12

[2022-10-10] Version 4.0.1
-Fixes using deprecated datarefs
-Adds support for Apple Silicon processor
-Does not support 32bit Windows anymore

[2022-11-09] Version 4.0.2
-Fixes a wrong dataref used for flap handle

[2023-05-07] Version 4.1.0
-Fixes "dataref replaced" warning in X-Plane 12's log file
-ALT and GND mode for transponder are synced in X-Plane 12
-Users now can add a keyboard shortcut or assign a joystick button to disengage the autopilot in the PFD

[2023-07-28] Version 4.1.2
-Changes the dataref used for getting pitch from sim/flightmodel/position/theta to sim/flightmodel/position/true_theta
-Adds custom datarefs and commands as below:

Datarefs:
SIMiONIC/CircuitBreakerDataRef      int[42]    not settable   Status for hardware circuit breakers, 0 for in, 1 for out
SIMiONIC/TargetCircuitBreakerDataRef      int    settable    The index number for the circuit breaker which will be tripped by command SIMiONIC/TripCircuitBreaker

Commands:
SIMiONIC/AutopilotDisengage    To disengage the autopilot in our G1000 app
SIMiONIC/TripCircuitBreaker    To trip the circuit breaker which index is set in the dataref SIMiONIC/TargetCircuitBreakerDataRef

[2023-08-10] Version 4.1.3]
-Deleted low pass filter algorithm for hardware flaps lever to adapt new firmwares

[2023-08-24] Version 4.2.0
-Adds automatic connection to hardware switch panel, standby gauges and pedestal

[2023-10-04] Version 4.2.1
-Fixes an issue causing altitude is not showed correctly with X-Plane 12 connected when atmosphere is not with ISA temperature

[2024-01-04] Version 4.3.0
-Added traffic data transmit for the new G1000 NXi app

[2024-01-17] Version 4.4.0
-Fixes a bug causing COM ports kept occupied after an auto-connection failure 
-Config file re-coded so there won't be any config loose any more
-Fixes a bug causing auto-connection hang
-Using datarefs to get temperature units instead of reading them from .acf files
-Reading temperatures from new datarefs in X-Plane 12

[2024-03-20] Version 4.4.1
-Added support for showing Rx/Tx for COMs in the G1000 NXi app, X-Plane 12 only